上传人：小又鸟 文档编号：2384694 上传时间：2021-12-14 格式：pdf 页数：16 大小：2.69mb. 《iso 14122-1-2001》由会员分享，可在线阅读，更多相关《iso 14122-1-2001（16页珍藏版）》请在凡人图书馆上搜索。 This part of ISO 14122 specifies minimum requirements that also apply when the same means of access is required as the part of the building or civil construction (e.g. stairs, stepladders, guard-rails) where the machine is installed, on condition that the main function of that part of the construction is to provide a means of access to the machine. e-standard AENOR UNE-EN ISO 14122-3-2017 PDF Spanish - AENOR UNE-EN ISO 14122-3-2017 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016) 34Page(s) Log In; 0 - $0.00; Checkout . Cheapest Codes and Standards Search: Browse Publishers This part of EN ISO 14122 is a type B standard as stated in EN 1070. This document is to be read in conjunction with clause 1.6.2 "Access to operating position and servicing points" and 1.5.15 "Risk of slipping, tripping or falling" of the essential safety requirements expressed in annex A of EN 292-2:1991/A1:1995. Buy ISO 14122-3:2016 Safety of machinery Permanent means of access to machinery Part 3: Stairs, stepladders and guard-rails from SAI Global Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users. Language(s): English, French. Published date: 05-27-2016. Publisher: International Unlike BS EN ISO 14122-3, which permits verification of safety requirements by calculation or testing, BS EN ISO 14122-4 subclause 5.5.1.1, Strength, states that the strength verification of a safety cage shall be made by testing - with no option for calculation permitted. However, see Clause 6 below. The two standards (ISO 14122-1 and ISO 14122-3) are partly similar, and partly different. EN ISO 14122-3 is approved for sales in Europe. Though ISO 14122-1:2006 is still available in Europe, the certification requirement is that the stair lifts comply with EN ISO 14122-3. The differences between the two standards are mentioned in a note below Iso 14122-3 pdf. leets desinavlag ni elbaliava si egnar etaG eeK ehT .yltcerrocni desu nehw ,diov suodrazah a ot dael nac noitcetorp fo smrof lanoitidart eseht sa ,sebut gnidils ro srab ,sniahc ot noitulos derreferp eht si metsys fo epyt sihTÂ Ã .setag eht fo ytilibailer latot erusne ot gnitset evisnetxe enogrednu sah metsys ehT .0901 NE ot c) Stairs (for detailed requirements see EN ISO 14122-3). Preferred angle of pitch is between 30 ° and 38 °. 5.5 Selection between stepladder and ladder When making the selection between stepladder and ladder at least the following points a) and b) shall be considered. ISO 14122-1:2001(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not EN ISO 14122-3,Safety of machinery — Permanents means of access to machinery — Part 3: Stairs, stepladders and guard-rails Page 8 BS EN ISO 14122-3:2001+A1:2010 EN ISO 14122-3:2001+A1:2010 (E) 3.1.16 clearance absolute minimum clear distance between any obstacle and the pitch line (c in Figure 1) measured at an angle of 90 from the pitch line 3.2 guard-rail device for protection against accidental fall or accidental access to a hazardous area, with which stairs ISO 14122-3:2016, Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails; EN 353-1:2014, Personal protective equipment against falls from a height — Part 1: Guided type fall arres