CC2640R2F-Q1 ACTIVE SimpleLink™ automotive qualified 32-bit Arm Cortex-M3 Bluetooth® Low Energy wireless MCU Data sheet CC2640R2F-Q1 SimpleLink™ Bluetooth® low energy Wireless MCU for Automotive datasheet (Rev. B) User guides CC13x0, CC26x0 SimpleLink™ Wireless MCU Technical Reference Manual (Rev. I) Errata CC2652R1. BLE Device Monitor connects to a BLE Central Device (Host) via a serial port. The following TI modules may serve as BLE hosts: CC2540 USB dongle, CC2650 LaunchPad, CC1350 LaunchPad and CC2640R2 LaunchPad. The host firmware is the HostTestApplication and is the same that BTOOL uses. The host firmware for all platforms is bundled with LAUNCHXL-CC2640R2 Quick Start Guide Datasheet by Texas Instruments View All Related Products | Download PDF Datasheet LAUNCH YOUR D ESIGN START @ Dev.ti.com/L AUNCHXL-CC2640R2 TI LaunchPad™ kit with SimpleLink™ Wireless MCU Microcontr oller development kit for rapid prototyping featuring the CC2640R2 microcontr oller P ART NO: LAUNCHXL-CC2640R2 CC2640R2 SDK Download Link. This specific version of BTool has been selected because it has support for the legacy TI OAD profile and the HCI command set supported by v1.41.17 is the most compatible with the CC2650 LaunchPad host_test image. TI-provided mobile applications are out of the scope of this document. Compared to the CC2650 LaunchPad, the CC2640R2 LaunchPad provides the following: • More free flash memory for the user application in the CC2640R2 wireless MCU • Out-of-the-box support for Bluetooth 4.2 specification • 4× faster Over-the-Air download speed compared to Bluetooth 4.1 Read PDF Ti Launchpad User Guide Ti Launchpad User Guide Getting Started with Texas Instrument's LaunchPad Introduction to LAUNCHXL-F28027 Launchpad (CCS and Simulink Demo External/XDS Direct Programming - CC2640R2 LaunchPad & CC26X2R1 LaunchPad. Programming the CC2640R2 LaunchPad or The LAUNCHXL-CC2640R2 from Texas Instruments is a SimpleLink™ Bluetooth® low energy CC2640R2F wireless MCU LaunchPad™ development kit. The CC2640R2F device has the first fully qualified Bluetooth 5 protocol stack for single mode Bluetooth low energy applications supporting high speed mode. CC2640R2F is part of the SimpleLink™ microcontroller (MCU) platform which consists of Two Button Menu. The Two Button Menu system is designed to utilize the two push buttons available on the CC2640R2 Launchpad. The left button (BTN1) is always used to cycle between options. The right button (BTN2) is used to activate the selected action or item. The Two Button Menu is set up by default to utilize the back channel UART present on The default simple_np configuration uses the LAUNCHXL-CC2640R2. This hardware configuration is shown in the below image: For custom hardware, see the Running the SDK on Custom Boards section of the BLE-Stack User's Guide for Bluetooth 4.2. An additional device will also be needed to act as the application processor. Software Prerequisites Prodigy 90 points. Part Number: LAUNCHXL-CC2640R2. Other Parts Discussed in Thread: CC2640. Hello, I am trying to implement an iOS app that does OAD on CC2640. Here is what I do: Issue OAD Reset command - write 1 to FFD1. Do a soft reset on 2640 using Smart RF programmer. Now the device advertises OAD service - follow the rest of the OAD Bluetooth products CC2640 ACTIVE SimpleLink™ 32-bit Arm Cortex-M3 Bluetooth® Low Energy wireless MCU with 128kB Flash Data sheet CC2640 SimpleLink™ Bluetoo